They told us that the cloudiness sometimes happens, but still doesn't explain the light coming on saying its low!!! The contact took the vehicle to the dealership on the first occasion and they couldn't find anything wrong with the vehicle. Theft light was on but went out at 2nd start. Wait 10 minutes until it turns off. I am using factory original keys, not replacements. I even bought the newrockies bypass module and performed the relearn several times and still nothing. It has not worked for me thus far, wondering if introducing this fix to the situation will be constructive? I know that only adds up to 515 but when you check it with a meter it will show 520, mine did anyway.
The other end solder on the orange with black stripe. Yours might be different and you might have to follow a step by step instruction. Or even a 3 way connect…. As soon as I plugged the radio fuse in,it was alive and running very well,i have it bolted down to a strong 4 wheel cart. When we bought it, the button for the doors to open automatically didn't work as well as the gas gauge.
This is a tight fit so watch your knuckles. The dealership informed the contact that the vehicle needed to be tuned up. Yes the orange wire with a black stripe goes to the crqnk relay. All previously learned keys will be erased from the system as soon as you program the first key. Also on the 10 min relearn reprogram trick all forums say that when you start the reprograming that the security light will flash or stay on solid, when the key is on and to wait for security light to stop flashing or turn off which takes 10 mins. This article describes how to reach these wires and modify the circuit to bypass the security module in the ignition switch.
I have the following problems in my 2000 Chevrolet Venture: Security light always on, fuel gauge will not reqister correct amout of gas, headlights flicker and also lights in information center located in overhead console also flicker and does not read correct information. Make sure the battery if fully charged because this procedure may take up to 30 minutes and you cannot start the vehicle during this time. Also melted plastic near contacts where some brake lamps plug into that housing. I used my other car and let it sit for 2 months. Today the car would not start and lo and behold I put it in neutral and it started on the 1st try! I don't feel this is a good solution but many others who indicated this problem said the dealer would not honor repair of this obvious design or manufacturers defect. He noticed that the vehicle decelerated and the instrument panel showed everything had lost power.
Since, we have replaced the heads, the water pump, rack and pinion, wheel hub, tie rod end, as well as replacing the head lights every couple months and now having problems with the brake lights. Do you wire the resistor 1 end to the black and 1 end with black and yellow together? Before owner realized it was their vehicle they live in apt complex they drove their vehicle through out day without incident. If you do not have power on a few of the fuses, then will need to look at some schematics. Now it wont start at all!! If you dont have it I can check it later when she comes back from the grandkids basketball game! Happened at least 3 times. Sometimes this will let the van start for awhile.
I repeated this process two more times and it worked for me. Do not leave out any step. Granted I likely had wrong resistor. Ok i have a 2001 silverado 1500 ls 5. Let me know what you find there and we will go from there.
Solder one end to the yellow wire that goes to the dash not toward the switch. I feel this presents a dangerous situation--that may either cause an accident, or a electrical fire within the car. It takes to long to explain. Then, the driver side brake light continued to go out due to the melting of the part of the bulb, not the bulb itself. Like I said truck ran fine before. Once the fuse housing is out, the negative terminal is located on the backside of the battery.
Always verify all wires, wire colors and diagrams before applying any information found here to your 2000 Chevrolet Venture. The contact stated that he was put on a waiting list for one week. The fuse housing is a large black box that sits atop the battery. I would go look for you but my wife is gone in it and I may never see it again!!! Adding More Information If you would like to help the Modified Life community by adding a car security wire schematic, car alarm wire diagram, car remote starter wire diagram, auto remote starter wire diagram or auto security wire diagram to our resource, please feel free to post any additional car wiring information about the 2000 Chevrolet Venture on this page. Windows had not been used due to cold weather. There is also rust along the van below the sliding doors. Most likely the problems is in the.