The consistency of the Automatic Transmission Fluid is much the same as to that of brake fluid on your Toyota Corolla, but never should one be used in place of the other. There are 18 bolts securing the transmission pan to the transmission. On my Corolla, the return hose was the one on the driver side red arrow. That's what I get for buying a first year model. This method utilizes the automatic transmission's internal pump to cycle out all spent fluid from the system while new fluid is added through the dipstick fill tube.
It is not recommended to use gasket adhesive to adhere the gasket to the pan. You should have about 3. The engine in your 2010 Toyota Corolla should be running when you perform a transmission fluid level check, otherwise it will be inaccurate. If fluid is coming out of the rubber line from the transmission to the cooler, reconnect it and try again with the other line. That might be another animal. Check under the car to ensure that there are no leaks.
While it may not be difficult to find replacement parts for Toyota vehicles, these days only the highest quality are required to fix your car or truck. This procedure should be done when the engine and transmission have been warmed up to near operating temperature to help suspend any contaminants within the old transmission fluid and to allow the old fluid to drain out more quickly. The reason that Toyota does not exchange all of the fluid is not clear to me. I noticed that my car was shifting really hard from 1st to 2nd gear and then it would run fine. In our city, they will take the old transmission fluid free at the hazardous waste disposal depot or will collect it with the recycle goods if it is placed in the original containers. Ensure that the car is stable and adequately supported prior to proceeding. Will the synthetic fluid be a problem? It was fantastic when it was new.
The white stains that you see on the bottom of the transmission pan is from the road salt that spread on the roads here in the winter. With the engine off, add 4 liters of clean transmission fluid to the transmission through the dipstick hole. However, most other references including a local independent transmission shop informed me they always drop the pan, clean the magnets, change the strainer, and exchange all of the fluid when they perform a transmission fluid service. Toyota brand products are among industry leaders for quality. Carefully pour the old transmission fluid from the catch basin in to the gallon jug marked with half quart lines. In reality, I find that 2.
Place large amounts of newspaper or cardboard under the car to catch any spills. Here is what the transmission looks like with the strainer removed. Tighten the drain bolt in the clockwise direction with the 10mm Allen Key or to just past hand tight or about 36 ft-lbs of torque. You bought your Corolla because its best-in-class value and driver satisfaction appealed to your senses; so why would you settle for anything but the best when it comes to great quality auto parts? Recommended torque for the drain plug is 36 ft. On mine, I only had to replace 2 liters in addition to the 4 liters I originally added, for a total of 6 liters.
If the transmission fluid level on your Corolla is low, you need to add fluid through the dipstick tube. Here is what mine looked like. I went around the pan twice just to make sure all bolts were properly torqued. Disclaimer Use this guide at your own risk! Just a floating gear shift. Remove the return line from oil cooler. Ensure that the longer bolt goes in the correct position. Really very unhappy with Toyota at the moment.
. The video above shows where the transmission fluid dipstick is located in your Corolla and how to check the transmission fluid level. Note that my local Toyota service department advised me that they only drain and fill. Continue replacing the old and adding the fresh until the fluid coming out of the transmission cooler into the bottle is a nice cherry red, like the new fluid. Then what was all the fuss about in the closed thread? As it is a log, it would clearly show all changes.
Snug the bolts up by hand using a nut driver. I found it easier to twist with a glove on. If I had to do it again, I think I could reasonably pare this down to about 2 hours. The green circles are short bolts and the red circle is a long bolt. We only sell parts from trusted brands like so that you can find quality parts you can count on.
Here is the link - Private message me for a price. I simply started a few bolts in each corner and that seemed quite adequate to hold the gasket in place. After this incident it worked flawlessly until March 15, where it started to shift in and out of overdrive and a few minutes later started slipping when attempting the overdrive shift. Took the car in for service. Time Required It took me 3.
Don't be a baby about it. Usually 6~7 liters are enough to do a complete flushing or if you can do a 10 liter flushing it will be great. This step netted me another ¼ liter of transmission fluid. It's not every day that you discover you need a replacement Automatic Transmission Fluid to fix your car or truck. Try not to scratch the pan.