Remove timing belt and driven sprockets. The in-line, one-way valve prevents the air in the hoses from flowing back to the dashpot. Remove camshaft caps and camshafts. The displacement for the pistons is 39. This outboard has starter of the electric type and power steering as well. Locks motor i n a fully tilted position.
The air flows through the in-line, one-way valve, and then to all of the carburetors. Re-install driven sprockets and timing belt. Gallons Imperial Gallons Liters Minimum Reserve Capacity Rating Battery Rating Electric Start Models of 35 Minutes and Cold Crank~ng. The iboats are another excellent source of information. We have fully boat tested this motor and it runs excellent.
The bore for this outboard is 2. Measure and record the exhaust valve clearance for cylinders 2 and 4. Compression is very strong on this engine at about 120psi even. Outboard Motors Nobody makes a more reliable, powerful, and efficient lineup of outboard motors than Mercury: , , , , and. You will be impressed by the power of this motor. A Piston Slap Nugget of Wisdom: My only additive of recommendation is Seafoam.
Open air vent on fuel tank cap. It is considerably less expensive than the … 2008-02-16 04:25:45 Truth About Cars Or sooner. Carefully pry up the valve pad and remove it. The parties submit to the non-exclusive jurisdiction of the courts in Queensland, Australia and any courts which may hear appeals from those courts in respect to any proceedings in connection with this agreement. After start-up, the current supplied form the electric power source and then flows to the electrothermal valves causing the wax in the valves to heat up. This motor has 2 cylinders and is a 2 stroke which means it will be light enough to be installed on most 30 hp capable boats.
If rewind starter becon-ies inoperative, the Sudden unexpected acceleration can cause niotor c a n be cranked u t i l ~ z l n g spare starter rope supplied in the following serious injury or death. Install tensioner spring and tighten timing belt tensioner. The iboats can likely help you find a lot of outboard information as it is arranged by subject. With carburetor turned upside down, and carb scale seated on inner edge, check float level from top of float to float bowl flange as shown. Install cylinder head cover and driven sprockets. The best products have the best dealers. Even if this information is the same as the original factory specs, boats are sometimes modified.
Suzuki Marine is truly unique. If no adjustment is necessary skip to step 11 on. Sure … 2011-08-28 23:55:44 SavannahNow The ethanol in our gasoline increases the cost to fill our cars, is heavily subsidized by taxpayers and has considerable environmental drawbacks. This motor is water cooled. Measure and record the exhaust valve clearance for cylinders 1 and 3. This additional air flows into the carburetors and mixes with the fuel from the main jets.
As the throttle is opened, the throttle lever rotates and pushes the throttle lever link rod. Covers Bigfoot Big Foot and Non-Bigfoot models. Turn the flywheel 360° clockwise. Engine Manual: Information on this page has come from multiple third parties and can not be guaranteed to be accurate. Thus, for safety and other reasons, it is a good idea to verify information here to make sure it matches up with your boat. Loosen timing belt tensioner bolt and remove tensioner spring.
This engine has power steering and a electric-type starter. The workshop Mercury repair manuals listed are available for instant download, allowing you to start working on your outboard motor now. The outboard marine mechanic should carefully read the text and become familiar with the Mariner marine engine service manual procedures before beginning the work. V-6 Cylinder, Two Cycle, Direct Injected. Clymer Mariner Outboard manuals are written specifically for the do-it-yourself enthusiast. Because this information has come from many sources we can not guarantee its accuracy.
This is a 2 cylinder model. Measure and record the intake valve clearance for cylinders 1 and 2. Install driven sprockets and timing belt. Engine Manual: Information on this page has come from multiple third parties and can not be guaranteed to be accurate. Disconnect spark plug leads and fuel hoses. However, enough information in Mariner outboard repair manuals is given for do-it-yourself or apprentice mechanics to correctly and safely perform repair work to their Mariner outboard motor and components. The iboats can likely help you find a lot of outboard information as it is arranged by subject.